Cracked gun stock repair epoxy

If you choose to try to repair it yourself go into midway usa, i think larry has a video on how to repair a cracked stock. What works very good is to mix it up and spread a line of epoxy over the crack. After wiping off the excess epoxy i let it set up for the 3045 minutes then do the razor blade scrape if necessary and then let it set for a full 24 hour cure. I had to do some recent stock repair on my k31 and although i was tempted to use gorilla glue, i knew from experience that it foams so i used gorilla wood glue, which according to the label does not foam. In my experience unreinforced cracks always result in more stock cracking. Course i work on a lot of military rifles, so i am used to cleaning the living daylights from an area to remove all traces of oil before making a repair. Being able to repair a cracked, chipped or broken shotgun stock is a valuable piece of knowledge for most hunters and shooting sports participants.

All too often well encounter wood rifle and shotgun stocks that have split due. I used the drill press to drill a couple of holes through the areas of the stock that had split. A thin coating of the epoxy was then applied to the face of the stock, avoiding any in the circular. Stockmaker gunstock repair, broken gunstock repair service. A simple stock repair you can do on your own part 1. Id like to repair the stock, but who knows a crack at that location may render the stock firewood. I never use just plain wood filler on a stock there are lot of ways to fix a chip depending on size and what you want it to look like when your done.

Remove the stock from your gun and inspect it for cracks. While im waiting for the replacement, i decided to try my hand at fixing the stock. Before a stock can be refinished, any cracks have to be glued. I worked in a yacht carpentry shop for a long time, where our epoxy use was measured in 50 gallon drums per year. Stock work can consist of a small repair, such as raising a dent in a stock with steam, or large repairs such as building a complete stock from scratch. However as to strength, the epoxy fix wins hands down in my experience. Besides the breaks, the grain on the back stock splintered. The other day i was cleaning the bolt on my cz 527, i had the gun leaning against the counter, and it fell over on the tile kitchen floor it cracked at the front of the stock, right up by the barrel. Stopping a crack from running is far easier than repairing a completed crack. The rifle is in very good condition but when i bought it, i failed to notice a crack in the butt stock. This resin rich paste grade epoxy system has been manufactured for repairing worn or scored shafts.

Tile epoxy adhesives free delivery possible on eligible. With this kit, plus acraglas and a varispeed drill, you can do quick, easy, suretohold repair jobs on cracked or broken stocks. Repairing stock cracks without pinning restoration. Mar 19, 2011 epoxy always does look plastic, as i have stated. I used plastic wrap to keep the clamps from adhering to the stock. The vast majority of my customers are much too far away to walk into my shop, but i am, you and i will communicate more than any gunsmith you have dealt with in the past. Its between the barrel bands and runs on an angle from the barrel channel rearward and down. This will pump the epoxy all the way through the crack until it comes out the other side. Just because a rifle has a broken stock does not mean it is not repairable. This is how i repaired an obviously serious break in the stock of a 1956 winchester model 88 rifle photo 1 using a west system 101 handy repair pack.

I think that there are several 2 part epoxy of high quality that do a good job, but stay away from gorilla glue on stocks. I have always used devon 2 ton clear epoxy which is very similar to acraglas but has a 30 minute work window. If i were you id cut out some of the cracked wood behind the recoil block, 18 to 14 inch would be fine, and fill with bedding epoxy with fiberglas strands across it, not jb weld or straight unreinforced acraglas. I think that there are several 2 part epoxy of high quality that. For cracks that might impact function of the gun mech, well, no, that would be a repairtoglock issue. I have a bolt action rifle stock with a crack in the wrist and would like to know what glues or epoxys would work best for the fix. The shattered gun stock to be repaired with a west system 101 handy repair kit. The buttplate area of the gun had also suffered damage to the toe and edges.

Some collectors take a dim view of wooden antiques being repaired with epoxy because repairs are not easily reversible like they would be if hide glue was used for repair instead. Friday night i took it to mitchell to put some rounds down range and i guess the shock of firing the rifle caused a piece to break off of the. With the soft wood found around the lugpin area on the mk ii rifles, youd need to splice in and then inlet new wood for the whole area to accomplish the strength of an epoxy fix. Sometimes the repairs can even add a bit of character to the rifle. The first step it to take the gun apart so the stock is free from the rest of the gun. Far too often, a perfectly good walnut stock is scrapped for a new one because of damage that could easily be repaired by its owner. The wood to metal contact areas will end up epoxy coated and will be oil and waterproof. I explained that repairing an antique with epoxy may affect its resale value if the potential purchaser objects to the repair. This is an epoxy gel that forms a very strong bond. How to repair a cracked or broken shotgun stock gone. Cracked stocks are rather easily repaired in this day due to the excellent glues we have at hand. I have repaired hundreds of stock cracks like that over the past 21 years using acraglas.

A little regular attention can save you a world of grief and cost in repairing a stock. I am not comfortable shooting it asis for fear of worsening it. A broken rifle stock is heartwrenching, but it neednt mean the end for that gun. I bought one last year that was a gunsmith special cracked stock for 199. Back under the heat lamp the stock went and it was carefully watched till the epoxy had just formed a skin on top that would not take a fingerprint. Nov, 2016 i have a shot gun someone dropped causing part of the wooden stock to break off. If there are serious cracks, have a gunsmith or qualified wood worker address them for you. Following are a few pics of the stockcrack before repair. This was a common way to repair a common problem with parkers and other fine doubles a split stock head. I would get some bedding compound like brownells acraglas and use it to fix the crack as well as glass bed the receiver tangs to the wood. Cracked stock near tang on a savage 99 repair shop recommendations. Remove the stock from the gun and take off all butt plates, recoil pads, grip caps, nuts, bolts, nails, rawhide, clamps, plastic model airplane parts or whatever type of old repair material. They sell fast so you need to check their site often.

I spread the fracture slightly, filled it, and clamped. I repaired the stock as best as i could, drilling holes and using makeshift dowels and it seems to have stabilized. Now, you may simply have a cracked stock with or without missing pieces of wood or you may have one actually broken in two or more pieces. But, i wouldnt use acraglass epoxy wfiber for wood stock repair just as i wouldnt use titebond an aliphatic resin for rifle and action bedding. Right now, the gun is wearing an 870p synthetic stock from the wilson combat sale. Then the staple was inserted and driven fully home. With epoxy, i wax the outside of the stock so it wont stick when it runs out and of course some always does. You dont want the screw holes to be too tight, as that would only encourage more splitting problems. I have had little luck with yellow glues on old gun stocks.

I open the crack as far as possible and give the epoxy a chance to run down inside then close and clamp the crack. Split stock repair content taken from forum post by jim williams weve all seen these guns for sale often in beautiful shape except for a pin, dowel or even a bolt through the stock head, cheektocheek. The gun was restocked in 1927 to modern day drop, cast, etc, with a. Use brownells acraglas liquid epoxy like f d shuster says. There are also many decorative or functional features that may be added. I have a beautiful sako wood gun stock rifle stock that has a crack that will require gluing and clamping. It is an older 2 part epoxy and many years ago when i worked in a gun shop it was the go to glue for stock work. With new modern glues and with the glue properly applied, the old break line is stronger than the wood ever was. I suspect it will part and maybe separate the stock into two pieces when the stock is removed. A fine sanding with 400 grit paper completed the stock preparation 7. Repair is my specialty, i can take your poor, tired, or broken stock and give it new life. Stock repair years ago my son had a skiing accident that resulted in one ski having delamination, although it was still in one piece, lengthwise. The stock is cracked through vertically in the area between the tangs. I have a cracked stock, and plan to repair it, by inserting a knife into the end grain, and putting glue in the crack.

If you were fixing a loose board in a building you would nail it back in place. Sand and then paint the entire stock with a flat or semigloss enamel. Apr 26, 2010 page 1 of 2 rifle stock repair lots of pics posted in milsurp rifles. I soaked the broken ends in acetone for about 5 minutes and brushed with a tooth brush a couple of times to remove any gun oil from the wood surface. I am going to strip the stock, repair the crack, and refinish. In this case, we are going to repair the split with just the epoxy. Suitable glue for repairing a cracked stock trap shooters forum. You can buy a small repair kit of accuglass and release agent from. The result is a small, shiny, brass dot on both sides and is quite strong. And although there is a shadow for the stock inletting picture, the crack protruded downward approximately 1 at the rearmost inletting. Cut screw flush to stock on both sides of stockrepair, polish with a cratex bit until flush. To begin, i went ahead with an epoxydowel repair, learning as i went along.

I then filled the holes with the epoxy and covered the threads of the screws with the epoxy and screwed them into place. Cracked stock near tang on a savage 99 repair shop. The repair to begin, i went ahead with an epoxydowel repair, learning as i went. Boses guns gun repair, restoration, and gunsmithing. I gave all of the surfaces a thick coat of epoxy 4. Simply gluing the stock back together will not produce a strong enough repair and you must add some structural strength. Heating andor thinning epoxy will effect its integrity, but probably not enough to matter in a situation like a hairline crack in a gun stock. Just remember, the color you see in the cup will darken somewhat when the acraglas is in the stock. Last week i picked up a 1974 marlin 336 chambered in. In the vast majority of cases it is an unusual situation on a stock that has been around for a long time and withstood normal use. A fresh crack repaired in this way can actually be invisible, but usually a gunsmith is handed a stock with two kinds of epoxy smeared on it and the crack is full of duco cement.

The doewl was inserted and epoxy was applied to the outside of the crack. I broke my synthetic stock on the left side where the op rod guide is located. Its not all the way through but with a little pressure it opens up. Fix that cracked shelf in the fridge and your glock at the same time. It isnt that the epoxy wont work, its just that its not the optimum glue for the repair. Lc smiths have kept stock makers in business since the turn of the last century, here are some pictures of a nice 2e that once had a 7 piece butt stock, shown in the first three pictures. This gun had a custom stock on it which was very poorly made and also had a cheek piece for a left handed shooter. Expertly refinishing and repairing your gunstock from ugly to. I used it often for rc planes and helicopters, and in gun stock work. Jun 03, 2015 the first step it to take the gun apart so the stock is free from the rest of the gun. Jan 24, 2012 i have a beautiful sako wood gun stock rifle stock that has a crack that will require gluing and clamping. I will be shooting this one, a reising m50 submachine gun, once the final nfa.

How to repair a cracked stock with brass rod and epoxy. Ive done this before with good results, but never on a crack this bad. Find a very capable gunsmith that has experienced broken stocks. Rifle stock repair lots of pics milsurp rifles long. Apr 11, 2015 a broken rifle stock is heartwrenching, but it neednt mean the end for that gun. Now please, before you go off about the aesthetics of this repair, please remember this is intended for beater stocks with little or no collector value. For cracks that might impact function of the gun mech, well, no, that would be a repair toglock issue. A good solid epoxy glue repair could be had on it and the finish touched up to where the break is very hard to see. I bet, based on how it cracked, that the stock was loose at one time, and the stock cracked due to battering from recoil. It appeared on top of the stock wrist only, about 334 in length. This stuff is so good you can i have used it to bond dissimilar materials to each other. Then squeeze and release the crack, or gently spread it and release it, whatever it takes to get the crack to open and close. Ive always used super glue to repair stock cracks, it works in the same way as gorilla glue, a little dampness helps it bond stronger. A strong repair that will outlast the rest of the gun is what im going for here.

Use epoxy for the repair as it is 100% solids and will not shrink. Acraglas came to mind as ive used it one other time nearly a decade ago to bed a match rifle during my more competitive smallbore days in my youth. Excellent product, i recommend this twopart epoxy to anyone who needs to make a long lasting if not permanent repair to just about anything made of wood, plastic, porcelain, masonry, and most metals. The ability to fill and repair small knots, cracks, and checks is vital for the.

I used dental tools to clean up the checkering and used furniture stripper on the old polyurethane finish. The mixed epoxy was poured into the raised grain cracks and then lightly clamped 6. Inject glueepoxy into crackapply pressure to crackrepair rubber surgical tubing,clamps, etc. The kit includes everything needed for a successful repair. I still use it and have repaired several stocks and perazzi type 3 forends with it. Dec 14, 2012 gunsmithing fixing a cracked buttstock and forend on a remington model 11 shotgun. When i make scales for knives, i always use epoxy, because im bonding two dissimilar materials. I do not know the extent of the crack, but i do know it goes completely through the stock. Pc products 72561 pcconcrete twopart epoxy adhesive paste for anchoring and crack repair, 8. It goes a couple inches down he stock, parallel to the barrel, and goes all the way through to the inside.

Gunsmithing fixing a cracked buttstock and forend on a remington model 11 shotgun. While the repair may show, the stock will be very strong and the gun usable again. I once took an old stock that was cracked at the wrist and glued with super glue, submerged in a bucket of water for 3 or 4 days and took it out to see what would happen and if i could split the repaired crack but it held solid. Put the wood stock in a closet or some other safe place as a remembrance of your father.

Have him repair it, then buy a good synthetic stock for the rifle. I put some paste wax along the edges of the stock near the seam of the repair, in case any epoxy seeped out, that way if any does seep out it will chip off when dry. Gunsmithing fixing a cracked buttstock and forend on a. Using a standard caulking gun is difficult with this, so redhead sells a gun that is supposed to work better. This is a discussion on synthetic stock repair within the the m14 forums, part of the m14 m1a forum category. Fixing a small crack on wrist of a rifle stock at the rear. The appliance repair plastic epoxy has worked great for me.